Overview
General Description
The Xactix E1 Xenon Difluroide etcher is an isotropic etch system, typically used for MEMS applications. XeF2 etching shows extremely high selectivity of silicon to silicon dioxide, photoresist, silicon nitride, and aluminum. Etch rates depend on the amount of exposed silicon, so recipes will depend on a particular sample. Silicon based samples up to 4" may be used.
Specifications
Etch rates: Highly dependent on sample size, from ~10 μm/min for small samples to ~0.2 μm/min for whole 6" wafers.
Selectivity:
1000:1 (Thermal/Low Temperature SiO2:Si)
>1000:1 Si3N4:Si
Low attack (depending on conditions) for Gold, Copper, and Si
Nonreactive with:
Al, Ni, Cr, Pt, Ga
PZT, MgO, ZnO, AlN, GaAs,
Photoresists, PDMS, C4F8, Silica Glass, PVC dicing tape, PP, PEN, PET, ETFE, and Acrylic
Available in either pulsed or continuous flow
Technology Overview
XeF2 exists as solid crystals, and sublimates to form a vapor-phase etchant. The process is a dry, vacuum based process that proceeds spontaneously, and thus does not rely on a plasma or other chemical activation. It proceeds as an isotropic etch for silicon, molybdenus, and germanium. The XeF2 etching rate does not depend on crystal plane, or silicon dopant content. As the XeF2-Si reaction is exothermic, a delay step may be added to cool the wafer between etch cycles and minimize any thermal issues.
For silicon, the etch proceeds as:
2XeF2 + Si => 2Xe + SiF4
Sample Requirements and Preparation
For well controlled silicon etching, a BOE dip should be done directly before XeF2 etching. XeF2 will etch SiO2 very slowly, so removing the native oxide layer will allow for a more uniform etch.
Whether the native oxide has been removed or not, all samples should be dehydrated directly prior to placement in etch chamber, either with IPA or a hotplate dehydration bake. The presence of adsorbed water on samples will result in the formation of both gaseous HF and a silicon flouride polymer on the sample surface. This polymer layer will reduce or completely stop etch progression, and will not be removed in either solvent soaks or O2 plasma.
Note: XeF2 will also etch Titanium, Titanium Nitride, Tantalum, Tantalum Nitride, and Tungsten at etch rates from 0-30 nm/min, strongly depending on the local temperature.
Standard Operating Procedure
Questions & Troubleshooting
How long should my cycle time be?
Cycle time should be set to allow all of the XeF2 vapor to react with exposed silicon. For large areas of exposed silicon, XeF2 will quickly react with the exposed areas, and the cycle time may be reduced. For a smaller chip, cycle times will need to somewhat longer to allow all of the XeF2 to react fully.
In order to tell that all XeF2 has reacted, the chamber pressure may be monitored. The etching reaction proceeds as 2XeF2 + Si -> SiF4 + 2Xe, meaning 2 moles of reactant gas will be present at the beginning of the etch step, and 3 will be present after the etch has completed. Therefore, the pressure in the chamber will increase somewhat while the etch is proceeding, and will level off after the etch has completed.
The etch rate on my sample seems nonuniform?
Uniformity is an inherent issue with XeF2 etching. There is a limited amount of etchant released in each cycle, and the local etch rate will depend on the amount of exposed silicon and available XeF2 vapor. In general, large exposed areas of silicon will show the worst uniformity, and regular patterns of small holes (with the rest of the wafer covered) will show the best uniformity. Minimizing unneeded exposed silicon will allow for faster and more uniform etching of the pattern.